PopularFX
Home Help Search Login Register
Welcome,Guest. Please login or register.
OverUnity Research > Benches > AlienGrey > Dally, Shark & Ruslan workbench
2024-11-26, 11:26:36
News: If you have a suggestion or need for a new board title, please PM the Admins.
Please remember to keep topics and posts of the FE or casual nature. :)

Pages: 1 ... 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 [35] 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 ... 101
Author Topic: Dally, Shark & Ruslan workbench  (Read 310314 times)
Topic Options img
img  Itsu
Re: Dally, Shark & Ruslan workbench « Reply #850 on: 2021-06-11, 18:18:16 »

Group: Elite Experimentalist
Hero Member
*****

Posts: 4159
pin 10 and 12 of U7 (IR2110)  are resp. 0V and 12V

Will try the U7 out and its pin 1 (not pin 7) to +15V later.        (Pin 1 goes to gate Q3, see below diagram which is as i have it now)

Itsu
   
img  Itsu
Re: Dally, Shark & Ruslan workbench « Reply #851 on: 2021-06-11, 20:25:55 »

Group: Elite Experimentalist
Hero Member
*****

Posts: 4159
I pulled out U7 (IR2110) and pulled up pin 1 to +15V using a 1K resistor.

I have a 1 Ohm 1% inductionfree resistor (csr) in the collector lead coming from the primary coil and measure 428mV across it, pointing to 428mA going through this primary.
The 12.8V collector PS shows 360mA, so i am not sure what is the most accurate value.


I had to remove the ground wire from the circuit as the scope probe ground lead would have caused a shortout.

Itsu
   
img  Vasik041
Re: Dally, Shark & Ruslan workbench « Reply #852 on: 2021-06-11, 20:44:40 »
Group: Guest
Quote from: Itsu on 2021-06-11, 20:25:55
I pulled out U7 (IR2110) and pulled up pin 1 to +15V using a 1K resistor.
I have a 1 Ohm 1% inductionfree resistor (csr) in the collector lead coming from the primary coil and measure 428mV across it, pointing to 428mA going through this primary.
The 12.8V collector PS shows 360mA, so i am not sure what is the most accurate value.
I had to remove the ground wire from the circuit as the scope probe ground lead would have caused a shortout.
Itsu

I have similar looking voltage/current indicators from ebay, they are not very accurate.
400ma probably to high for 12v, for beginning I would suggest increasing slightly R17 so that current decrease to 100-200ma (not sure).

Vasik
   
img  Itsu
Re: Dally, Shark & Ruslan workbench « Reply #853 on: 2021-06-11, 21:02:30 »

Group: Elite Experimentalist
Hero Member
*****

Posts: 4159

I agree,   i will change R17 to a 5K potmeter to adjust to 100-200ma

Itsu
   
img  verpies
Re: Dally, Shark & Ruslan workbench « Reply #854 on: 2021-06-11, 21:17:11 »

Group: Professor
Hero Member
*****

Posts: 3499
Quote from: Itsu on 2021-06-11, 17:15:41
Pin 1 has 0V   same as pin 7.
IF
pins 3, 9 are at +15V, and
pin 2, 11, 13 are grounded, and
pin 12 is at +12V

THEN
pin 1 must be at +15V unless something is pulling it down drastically ...or the IR2110 chip is broken.
   
img  Itsu
Re: Dally, Shark & Ruslan workbench « Reply #855 on: 2021-06-11, 21:41:09 »

Group: Elite Experimentalist
Hero Member
*****

Posts: 4159

Ok,  i will check again the pin 1 value tomorrow.


In de mean time i added a 5K pot in series with R17 (3.3K) and had to use the whole range (5K) to get to 150mA collector current at 12V.
This means that R17 should be in the 8K range.

Itsu
   
img  AlienGrey
Re: Dally, Shark & Ruslan workbench « Reply #856 on: 2021-06-12, 00:49:30 »
Group: Guest
Quote from: verpies on 2021-06-11, 21:17:11
IF
pins 3, 9 are at +15V, and
pin 2, 11, 13 are grounded, and
pin 12 is at +12V

THEN
pin 1 must be at +15V unless something is pulling it down drastically ...or the IR2110 chip is broken.
You need to pull up pin 6

Quote from: Itsu on 2021-06-11, 17:15:41

    Pin 1 has 0V   same as pin 7.

IF you missed out pin 6 , 3, 9 O0
pins 3, 9 are at +15V, and
pin 2, 11, 13 are grounded, and
pin 12 is at +12V

THEN
pin 1 must be at +15V unless something is pulling it down drastically ...or the IR2110 chip is broken.  may be not!
   
img  verpies
Re: Dally, Shark & Ruslan workbench « Reply #857 on: 2021-06-12, 01:38:00 »

Group: Professor
Hero Member
*****

Posts: 3499
Quote from: AlienGrey on 2021-06-12, 00:49:30
You need to pull up pin 6
Why?
Pin 6 is the high supply for the output at pin 7.

Itsu wrote that he is not driving the Q3 from pin 7. He is driving it from pin 1.

Quote from: Itsu on 2021-06-11, 16:51:36
...it's driven by pin 1 of the IR2110.
   
img  Itsu
Re: Dally, Shark & Ruslan workbench « Reply #858 on: 2021-06-12, 09:16:46 »

Group: Elite Experimentalist
Hero Member
*****

Posts: 4159

IR2110 pin 6 is at +15V together with pin 3.

Slight correction; pin 9 is at +12V, not +15V


Itsu
   
img  Vasik041
Re: Dally, Shark & Ruslan workbench « Reply #859 on: 2021-06-12, 09:28:32 »
Group: Guest
Here is updated schematic to avoid further confusion...
   
img  verpies
Re: Dally, Shark & Ruslan workbench « Reply #860 on: 2021-06-12, 09:46:23 »

Group: Professor
Hero Member
*****

Posts: 3499
Quote from: Itsu on 2021-06-12, 09:16:46
Slight correction; pin 9 is at +12V, not +15V
The datasheet of the IR2110 in the section "Recommended Operating Conditions" recommends, that the pin 9 is between 3V and 20V above ground (Vss) so +12V is fine.  This voltage affects the interpretation of the input logic levels appearing on pins 10 and 12. For example, if you were using 5V logic chips to drive the input pins 10 and 12 then pin 9 should be connected to 5V (the supply rail of these 5V logic chips). Also, the voltage on pin 9 must not be smaller than the voltages on pins 10, 11, 12.  (if it is smaller by more than 300mV then the chip risks damage).

The takeway is that with these conditions, the pin 1 must be at +15V and if it is not, then something is shorting it to ground or the IR2110 chip is bad.
   
img  Itsu
Re: Dally, Shark & Ruslan workbench « Reply #861 on: 2021-06-12, 09:56:23 »

Group: Elite Experimentalist
Hero Member
*****

Posts: 4159

Thanks for the new diagram.

Concerning the pin 1 being at 0V, when yesterday i had everyting in place (no pulled out chips or pulled up pins), i was monitoring both pins 1 and 7
and both had pulses on them and the kacher was working so i think there is nothing wrong with the IR2110.

But i will redo the pull out U10 and latch up its pins 10, 12 and 13 to find out why i did not had +15V on IR2110 pin 1 later today.


Itsu
   
img  Itsu
Re: Dally, Shark & Ruslan workbench « Reply #862 on: 2021-06-12, 16:20:28 »

Group: Elite Experimentalist
Hero Member
*****

Posts: 4159
I have replaced R17 with a 8.2KOhm resistor and with U7 (IR2110) removed and its pin 1 wired to +15V, i have 130mA @ 12V running through the collector.

I reinstalled U7 (IR2110), removed U10 and wire its pins 10, 12 and 13 to +12V and still have the 130mA running through the collector.
So now IR2110 pin 10 is 0V, pin 12 is +12V, pin 7 is 0V and pin 1 is +13.3V activating Q3 and thus Q5 etc.

Not sure what happened yesterday during that same last setup but i never had the 12V PS show the 130mA current, nor did i saw +15V on IR2110 pin 1.


Anyway, after reinstalling all the chips etc. and firing up the kacher, the "umph" seems gone now from the kacher as the 12V PS for the primary coil shows no current and a NE-2 neon does not light up.
The scope probe near by does show some minimal activity (typical switched kacher ringing signal).

I now probably need more voltage (100V) on the collector to get the "umph" back.

Itsu   
   
img  verpies
Re: Dally, Shark & Ruslan workbench « Reply #863 on: 2021-06-12, 17:23:03 »

Group: Professor
Hero Member
*****

Posts: 3499
Quote from: Itsu on 2021-06-12, 16:20:28
So now IR2110 pin 10 is 0V, pin 12 is +12V, pin 7 is 0V and pin 1 is +13.3V
I hate to nitpick but if pin1 really is 1.7V below pin3 (+15V) then this is too much of a voltage drop according to the datasheet when the lowside driver is on.
How much current is flowing out of pin1 ?
   
img  Itsu
Re: Dally, Shark & Ruslan workbench « Reply #864 on: 2021-06-12, 17:30:49 »

Group: Elite Experimentalist
Hero Member
*****

Posts: 4159

Actually its 15V versus 13.6V, so 1.4V below.   
So what is causing this voltage drop?

Itsu
   
img  verpies
Re: Dally, Shark & Ruslan workbench « Reply #865 on: 2021-06-12, 17:34:13 »

Group: Professor
Hero Member
*****

Posts: 3499
Quote from: Itsu on 2021-06-12, 16:20:28
I reinstalled U7 (IR2110), removed U10 and wire its pins 10, 12 and 13 to +12V...
Are you sure this is not a typo?
Pin13 is the VSS, which is the logic ground and should be at 0V.
Pins 2,5,11 should be grounded, too.
   
img  Itsu
Re: Dally, Shark & Ruslan workbench « Reply #866 on: 2021-06-12, 17:44:35 »

Group: Elite Experimentalist
Hero Member
*****

Posts: 4159

I was talking about U10 (4093).
   
img  Itsu
Re: Dally, Shark & Ruslan workbench « Reply #867 on: 2021-06-12, 17:45:40 »

Group: Elite Experimentalist
Hero Member
*****

Posts: 4159

Hmmmm,   i removed U10 again and pulled up its 10, 12 and 13 to +12V, and we have +12V on IR2110 pin 12, but nothing on pin 1 (nor pin 7).
Also no current pulled from the 12V PS, so same situation as yesterday, so something is not right.

Itsu
   
img  verpies
Re: Dally, Shark & Ruslan workbench « Reply #868 on: 2021-06-12, 17:55:22 »

Group: Professor
Hero Member
*****

Posts: 3499
Quote from: Itsu on 2021-06-12, 17:44:35
I was talking about U10 (4093).
OK, that changes things, so the entire tc point is at +12V and this means that the IR2001.12 should be at +12V and the IR2110.10 should be near 0V.

Quote from: Itsu on 2021-06-12, 17:45:40
I removed U10 again and pulled up its 10, 12 and 13 to +12V, and we have +12V on IR2110 pin 12, but nothing on pin 1 (nor pin 7).
So what are the voltages on other IR2110 pins ?
Especially on IR2110.11 ?
   
img  Itsu
Re: Dally, Shark & Ruslan workbench « Reply #869 on: 2021-06-12, 19:58:24 »

Group: Elite Experimentalist
Hero Member
*****

Posts: 4159
Quote from: verpies on 2021-06-12, 17:55:22
OK, that changes things, so the entire tc point is at +12V and this means that the IR2001.12 should be at +12V and the IR2110.10 should be near 0V.

Correct.

Quote
So what are the voltages on other IR2110 pins ?
Especially on IR2110.11 ?

IR2110.11  is 0V,    see short video of all the pin's measured:   https://youtu.be/4e_ldFBP9BI


Pins measured:

1=0V
2=0V
3=15.06V
4=0V
5=0V
6=15.06V
7=0V
8=0V
9=12.1V
10=0V
11=0V
12=12.1V
13=0V
14=0V

Itsu
   
img  Itsu
Re: Dally, Shark & Ruslan workbench « Reply #870 on: 2021-06-12, 20:09:42 »

Group: Elite Experimentalist
Hero Member
*****

Posts: 4159

Ok,  i fiddled around with pin 1 of the IR2110 and suddenly there is 13.75V on it, so there is a defective pin1 (chip) i guess  (can't get it to fail now  :D ), but i will replace the IR2110.

Itsu
   
img  Vasik041
Re: Dally, Shark & Ruslan workbench « Reply #871 on: 2021-06-12, 20:20:48 »
Group: Guest
Quote from: Itsu on 2021-06-12, 20:09:42
Ok,  i fiddled around with pin 1 of the IR2110 and suddenly there is 13.75V on it, so there is a defective pin1 (chip) i guess  (can't get it to fail now  :D ), but i will replace the IR2110.

It could be that when power supply was damaged, it killed something on PCB.
I would suggest carefully check that everything works as expected.

Vasik
   
img  verpies
Re: Dally, Shark & Ruslan workbench « Reply #872 on: 2021-06-12, 20:31:20 »

Group: Professor
Hero Member
*****

Posts: 3499
Quote from: Itsu on 2021-06-12, 19:58:24
IR2110.11  is 0V,    see short video of all the pin's measured:   https://youtu.be/4e_ldFBP9BI
With the voltages you measured, pin 1 should be close to +15V because this pin is driven by an internal MOSFET (circled in red), which has only several mOhms of internal resistance.
I was suspecting pin 11 to be floating or pin 1 to be shorted to ground ...or being pulled down so hard that the internal MOSFET's voltage drop manifests itself across its RDS_ON.
Another reason for the malfunction could be the UV Lockout due to improper power up sequence.  There should not be an UVL above +10V on pins 3 & 6, though.

Quote from: Vasik041 on 2021-06-12, 20:20:48
It could be that when power supply was damaged, it killed something on PCB.
I would suggest carefully check that everything works as expected.
Yes, I suggest pulling out the IR2110 and using an ohmmeter to do sanity check when the circuit is NOT powered.
Maybe its IC socket has a short between pins 1 and 2 ...or the PCB.

The MOSFET inside the IR2100 (circled in red) really should pull the pin 1 up to whatever voltage is on pin 3, unless a large current is drawn from pin 1 and a significant voltage drop occurs across the RDS_ON of the internal MOSFET.
   
img  Itsu
Re: Dally, Shark & Ruslan workbench « Reply #873 on: 2021-06-12, 21:19:47 »

Group: Elite Experimentalist
Hero Member
*****

Posts: 4159

I cannot find anything obvious wrong now.

Below screenshot shows the pin 1 (red) signal compared to the pin 3 (yellow) signal (IR2110).

So 15V v 13.8V, so we loose 1.2V.

We have a voltage drop of 23mV across the 6.8 Ohm resistor (R11) to gate of Q3, so 3.3mA running there.

Itsu
   
img  Vasik041
Re: Dally, Shark & Ruslan workbench « Reply #874 on: 2021-06-13, 10:24:03 »
Group: Guest
Earlier we discussed fish-like signals, and there were doubts that they are real.
I'he been looking for good scope traces...here they are, made with analog and digital scopes.

source: https://realstrannik.com/forum/ustanovka-kulabukhova/1327-ustanovka-za-5000-evro-sergej-panov?start=80#102194
https://realstrannik.com/forum/ustanovka-kulabukhova/1327-ustanovka-za-5000-evro-sergej-panov?start=160#102391
   
Pages: 1 ... 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 [35] 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 ... 101
« previous next »


 

Home Help Search Login Register
Theme © PopularFX | Based on PFX Ideas! | Scripts from iScript4u 2024-11-26, 11:26:36